What properties define acrylic plastic

Cheap small plexiglass acrylic plastic polishing machine

 

Product introduction:
Flame polishing machine uses electrochemical technology to extract hydrogen and oxygen gas from water through special reaction device. The hydrogen combustion, oxygen is used for combustion, flame concentration, zero pollution, high production efficiency, and its flame combustion is pure blue. It doesn't produce smoke and dust. It is particularly suitable for polishing plexiglass, acrylic and other materials. It is one of the necessary equipment for crystal word making, so it is also called a plexiglass flame polishing machine.
Model: DSA-F202 (double gun)
Power supply: 220V / 50Hz / 60Hz (configure traditional pure copper transformer rectifier constant power supply)
Power: 1000W (adjustable)
Fire temperature: 0-3000 degrees (adjustable)
Gear adjustment: set 4 gear adjustment
Cell capacity: 1000ml
Pure water consumption: 40ml / hour
The amount of electrolyte is reduced: 6 ml / hour
Gas production: 160 liters / hour
Body size: 45cm * 30cm * 35cm
Weight: 31Kg
Product use: plexiglass (acrylic) irregular surface thermal polishing
Machine maintenance:
1. Before every work shutdown, first blow away from the flame and then pull out the exhaust switch of the spray gun, wait for the spray gun to cool down and gently put it on the machine.
2. Do not use the water for a long time, and rinse it with pure water.
3. Please use electrolytic capacitor powder specified by the manufacturer, the purity is high, the corrosion of the water tank is reduced, and the service life of the machine is extended.
Instructions for use:
1. After the power is turned on, the working and the power indicator light are on, the fan is turned on, and the air outlet has a wind feeling. According to the thickness of the acrylic, the needle is selected, the needle is screwed clockwise into the spray gun, and the open flame is ignited.
2. After several hours of use, it is found that the electrolyte level shows a significant drop, and distilled water needs to be added in time.
3. Add alcohol to the booster.
4. When the machine is used, the temperature of the body will gradually increase, and the parts will reach 70 degrees, which is a normal phenomenon. However, if the smoke or noise is found in the machine, please turn off the machine immediately.
Use.
5. Ensure that the pressure is sufficient (0.02-0.08 MPA) to open the gun valve ignition.
6. if with distilled water during use; Do not exceed the defined water level when it is accidentally flowed into the machine; Be sure to wipe it clean before use.
7. Do not place any metal objects on the machine to avoid short circuits.
8. Proper use of electrolytes and accessories to ensure machine performance and longevity.
Warranty: The whole machine is guaranteed for one year, please rest assured to buy!

 

 

Application range
1, acrylic irregular surface thermal polishing.
2, Spot and surface soldering of metal jewelry such as gold, silver, copper, lead-tin alloy.
3, glass-sealed bottle sealing, in line with GMP standards.
4, the enameled wire of the motor rotor, the outlet wire, etc. are directly fused, no need to paint.
5, Fusion of LED chips, peeling of computer cables.
6, the hinge of the metal eyeglass frame.
7, cutting and splicing of quartz glass and fine stacks.
8, the sand hole of the tooth shape is repaired and fused.
9, battery lead-tin alloy plate fusion.
10, local treatment of metal parts
Multi-functional high efficiency
The hydrogen and oxygen are electrolyzed by simple distilled water, and the water is cooled and filtered to reduce the flame temperature, heat and pressure, and the flame output is improved in order to obtain an economically high temperature source. The characteristics are as follows:
1, combustion is distilled water, a small amount of alcohol (non-active fuel), raw materials are easy to obtain, and storage is safe.
2, It is specially made from water vapor after burning and will not pollute the environment.
3, the surface of the object to be heated is pure and has no residue.
4, strong and durable structure, long service life and less trouble.
5, the model is lightweight and easy to use.
Random configuration
1. 1 set of special alkali-resistant tube; 500g / bottle of electrolytic powder.
2. One small funnel; a set of small seals.
3. F308 type is equipped with a large spray gun with two joints, two F303 spray guns, two F202 spray guns, and one F101 spray gun.
4. a copy of the instruction manual.
Instructions for use
1. After the power is turned on, the working and power indicator light are on, the fan is turned on, and the air outlet has a feeling of air. According to the thickness of the organic work, select the needle, screw the needle clockwise into the spray gun, and ignite the light to work.
2. After a few hours of use, it is found that the electrolyte level shows a significant drop, and distilled water needs to be added in time.
Adding distilled water steps:
1) blow out the gun and turn off the power.
2) slowly unscrew the water cap.
3) add distilled water to the standard scale.
4) pull out the water cap and turn it on again.
3. Add alcohol to the booster as above.
4. When the machine is used, the temperature of the machine will gradually increase, and the parts will reach 70 degrees, which is a normal phenomenon. However, if the machine emits smoke or noise, turn off the machine immediately, and use it after the inspection.
5. Make sure the pressure is sufficient (0.02-0.08 Mpa) to open the gun valve to ignite.
6. When adding distilled water while using, do not exceed the defined water level. If water doesn't flow into the machine, be sure to wipe it clean before using.
7. Do not place any metal objects on the machine to avoid short circuits. polishing machine for acrylic
8. Proper use of electrolytes and accessories to ensure machine performance and longevity.
Maintenance and precautions
1. It is only necessary to add distilled water to electrolytic capacitors cylinder after the first use.
2. When adding distilled water to electrolytic capacitors cylinder and adding alcohol to the booster, please do not exceed the arrow standard scale, otherwise the work effect will be poor or the machine will malfunction.
3. The normal use period of the electrolyte is about six months. It is normal to use black while. If the fire is weakened after six months, please replace the electrolyte.
4. the bottom of the machine has a drain on the bottom that can be unloaded directly. If it is not a model, please use a hose to suck the electrolyte into the cylinder (no suction is allowed). Don't put the polisher down to discharge the electrolyte. (Please refer to the electrolyte instructions).
5. Replace the booster alcohol method: loosen the alcohol replacement silk and wash the booster with a small amount of alcohol.
6. Note that the gun nozzle should not be burned towards the user during ignition and ignition.
7. If the machine is used to generate abnormal noise (or hear the sound of rays), do not panic and worry, it is due to improper operation or local air leakage. Re-replace the hose or check the gas pipeline. When it is gas discharge, it can be used normally. polishing machine for acrylic
? 8. The most important thing to use in normal machine is to pay attention to adding water. (Use funnel to add water) to keep working at normal water level. Check if alcohol is in normal position (about half of alcohol tank) after starting for 3 minutes every day. Alcohol is used to filter water vapor (We recommend replacing the alcohol once every 2 days, or if you find that the gun has moisture, you have to change the alcohol in time.) The electrolyte is usually replaced once every 3 -6 months. Usually, the water can be added. At the lower temperature, the gas will be produced. Slow down, don't worry, after about 20 minutes, the gas will reach normal after the machine temperature rises.
9. Because the machine is a metal chassis, it must be a reliable ground wire.
10. Put the tip of the gun into the water or hit it out with your mouth when the flame is off, then turn off the power.
Electrolyte instructions
The raw material for the electrolysis of the electrolyte to produce gas is a consumable product. It is in the form of a white piece. It has a lifespan of over 6 months after dissolving. It sucks. Please do not touch the skin and the entrance to the eye. Please rinse with water. Please use a funnel when adding water, add carefully! Never let water flow into the machine to avoid short-circuiting the machine. polishing machine for acrylic
For newly purchased machines, first check whether the white hose (water level indicator) on the front of the machine has liquid (usually need to take the logistics and transportation machine, we do not add electrolyte to prevent inverted leakage). For example, please refer to the following ratio. Adding electrolyte. First observe the model, you must use pure water or distilled water. If your machine is used for more than 4-6 months, if the machine is found to be slower than before, when it is usually used, you will need to replace the electrolyte, and all of the liquid in the cylinder will be drained and added back . The method of dissolving the electrolyte usually is as follows: first pour the white wafer into a stainless steel or ceramic container (disable aluminum crucible or plastic tray), then add pure water or distilled water, and then dissolve completely before adding to the machine.